I have emails on Yahoo!, Gmail, Hotmail and GMX. Each apartment in kuala lumpur these provide different level of services. For one thing, new streamyx like Gmail's 20mb of file size for transmitting files and its improve broadband speed good anti-spam system.
GMX is also great with large files and internet providers has a built-in online harddrive. I just don't know how to put links within the message. I find it very troubling.
Hotmail... I don't really malaysia malaya Hotmail much. I find its interface very boring.
Yahoo!, now tm streamyx bill the email service cable internet provider I've been using the longest. I think it's been 10 years since I first opened my very first email account and it's with Yahoo. It's no longer active though.
But about a month ago, I had a document file that I saved in one of my folders in my Yahoo email. When I needed it so badly, I tried logging into my Yahoo account but it so happened that they were doing some sort of maintenance and their services will not be available again for the next 12 or so hours.
I panicked! It's the only file that I have because I was very stupid not to malaysia tourist any copies.
So now whenever I save a file online, I make sure that I save copies on my other email accounts, just in case.
When designing your LAN or WAN the logical solution in relation to your expected usage may often indicate multiple T1 lines. setup streamyx account this case bonded T1 could be the best choice. However, before you jump you need to know just what a bonded T1 really is and what it can....and can't....do for you.
A bonded T1 just means that the you have two T1 lines (from the same provider) which have been joined together in a special way so that you can use the combined total of 3.0 Mbps of Internet data or the 46 channels for voice/phone use. You cannot bond T1's together if they are not through the same provider.
If you were to have two T1's, unbonded, then you could not use the full 3.0 Mbps of bandwidth all at once. For example, if you cheap hotel kuala lumpur a speed test, you wouldn't be able to get a result of "3.0 Mbps", the max you could download/upload at any one time would be 1.5 Mbps, even though you had two T1's. I know it doesn't make sense because you think that 1.5+1.5=3.0. It doesn't work like that. Unless your T's are bonded, you can only use the 1.5 Mbps of bandwidth that each line provides....seperately. You can do two download tests, at separate download test sites, and get a full 1.5 Mbps reading at each download site. But with out bonding, there isn't a way of getting a test result of 3.0 Mbps. Think of it in terms of cars: You can either have two slow Datsun pickups or one Ram 4x4 with a 5.7L Hemi. Sometimes, two slow pickups are better for reliability than one big Ram 4x4, but not as big and fast.
There are exceptions to this of course, and there's probally better ways of explaining it, but this will give you a general idea.
You can bond quite a few T1 together by the way, you're not limited to just two. The maximum is usually around 4 T1's although some have gone as far as 8. However, if you go beyond 4 bonded T1's it makes much more sense to start tmnet at a fractional/burstable DS3. That decision than rests on the combination of capability requirements and cost efficiency in relation to the intended application(s).
It's best that you use the services of a telecommunications consultant to walk you through all of your choices for network johor utilizing a bonded T1. If you need more than what a bonded T1 can provide....such as a fractional or full DS3....you should also make use of consultant srevices. Many such services are usually no cost to you....and will enable you to more effectively and efficiently find the best solution for your specific application(s).
Michael is the owner of FreedomFire streamyx bridge DS3-Bandwidth.com and Business-VoIP-Solution.com. Michael also authors Broadband Nation where you're always welcome to drop in and catch up on the latest BroadBand news, tips, insights, and ramblings for the masses.
No comments:
Post a Comment